December 2015 Most Viewed Documents for Materials

  1. The influence of grain size on the mechanical properties ofsteel
    Morris Jr., J.W. (2001)

    859

  2. Heat Treatment Procedure Qualification -- Final Technical Report
    Robert C. Voigt (2004)

    776

  3. Fatigue design curves for 6061-T6 aluminum
    Yahr, G.T. (1993)

    749

  4. Charpy impact test results on five materials and NIST verification specimens using instrumented 2-mm and 8-mm strikers
    Nanstad, R.K.; Sokolov, M.A. (1995)

    546

  5. Mechanical properties and energy absorption characteristics of a polyurethane foam
    Goods, S.H.; Neuschwanger, C.L.; Henderson, C.; Skala, D.M. (1997)

    455

  6. Results of charpy V-notch impact testing of structural steel specimens irradiated at {approximately}30{degrees}C to 1 x 10{sup 16} neutrons/cm{sup 2} in a commercial reactor cavity
    Iskander, S.K.; Stoller, R.E. (1997)

    396

  7. Ferrite Measurement in Austenitic and Duplex Stainless Steel Castings - Literature Review
    Lundin, C.D.; Zhou, G.; Ruprecht, W. (1999)

    308

  8. Overcoming residual stresses and machining distortion in the production of aluminum alloy satellite boxes.
    Younger, Mandy S.; Eckelmeyer, Kenneth Hall (2007)

    246

  9. Comparison of three Ni-Hard I alloys
    Dogan, Omer N.; Hawk, Jeffrey A.; Rice, J. (Texaloy Foundry Co., Inc., Floresville, Texas) (2004)

    240

  10. Enhancing thermal conductivity of fluids with nanoparticles
    Choi, S.U.S.; Eastman, J.A. (1995)

    231

  11. Grain refinement of permanent mold cast copper base alloys. Final report
    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M. (2004)

    218

  12. A study of polyether-polyol- and polyester-polyol-based rigid urethane foam systems
    Madden, J.P.; Baker, G.K.; Smith, C.H. (1971)

    203

  13. Work Functions of the transition Metals and Metal Silicides
    Drummond, T.J. (1999)

    196

  14. Verification of Allowable Stresses In ASME Section III Subsection NH For Grade 91 Steel & Alloy 800H
    R. W. Swindeman; M. J. Swindeman; B. W. Roberts; B. E. Thurgood; D. L. Marriott (2007)

    195

  15. Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review
    Doebling, S.W.; Farrar, C.R.; Prime, M.B.; Shevitz, D.W. (1996)

    162

  16. PROPERTIES AND PERFORMANCE OF CEMENT-BASED GROUTS FOR GEOTHERMAL HEAT PUMP APPLICATIONS.
    ALLAN,M.L. (1999)

    154

  17. Final Report, Volume 1, Metallurgical Evaluation of Cast Duplex Stainless Steels and their Weldments
    Wen, Songqing; Lundin, Carl, W.; Batten, Greg, W. (2005)

    117

  18. P-type doping of GaN
    Wong, R.K. (2000)

    109

  19. ADVANCED COMPOSITE WIND TURBINE BLADE DESIGN BASED ON DURABILITY AND DAMAGE TOLERANCE
    Galib Abumeri; Frank Abdi (PhD) (2012)

    106

  20. Yield improvement and defect reduction in steel casting
    Kent Carlson (2004)

    100

Last updated on Tuesday 14 June 2016