September 2015 Most Viewed Documents for Materials

  1. The influence of grain size on the mechanical properties ofsteel
    Morris Jr., J.W. (2001)

    805

  2. Fatigue design curves for 6061-T6 aluminum
    Yahr, G.T. (1993)

    649

  3. Heat Treatment Procedure Qualification -- Final Technical Report
    Robert C. Voigt (2004)

    583

  4. Charpy impact test results on five materials and NIST verification specimens using instrumented 2-mm and 8-mm strikers
    Nanstad, R.K.; Sokolov, M.A. (1995)

    454

  5. Mechanical properties and energy absorption characteristics of a polyurethane foam
    Goods, S.H.; Neuschwanger, C.L.; Henderson, C.; Skala, D.M. (1997)

    331

  6. Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review
    Doebling, S.W.; Farrar, C.R.; Prime, M.B.; Shevitz, D.W. (1996)

    317

  7. Ferrite Measurement in Austenitic and Duplex Stainless Steel Castings - Literature Review
    Lundin, C.D.; Zhou, G.; Ruprecht, W. (1999)

    284

  8. Impact limiter tests of four commonly used materials and establishment of an impact limiter data base
    McMurtry, W.M.; Hohnstreiter, G.F. (1995)

    250

  9. Verification of Allowable Stresses In ASME Section III Subsection NH For Grade 91 Steel & Alloy 800H
    R. W. Swindeman; M. J. Swindeman; B. W. Roberts; B. E. Thurgood; D. L. Marriott (2007)

    235

  10. Results of charpy V-notch impact testing of structural steel specimens irradiated at {approximately}30{degrees}C to 1 x 10{sup 16} neutrons/cm{sup 2} in a commercial reactor cavity
    Iskander, S.K.; Stoller, R.E. (1997)

    224

  11. Comparison of three Ni-Hard I alloys
    Dogan, Omer N.; Hawk, Jeffrey A.; Rice, J. (Texaloy Foundry Co., Inc., Floresville, Texas) (2004)

    220

  12. Overcoming residual stresses and machining distortion in the production of aluminum alloy satellite boxes.
    Younger, Mandy S.; Eckelmeyer, Kenneth Hall (2007)

    198

  13. Work Functions of the transition Metals and Metal Silicides
    Drummond, T.J. (1999)

    160

  14. A study of polyether-polyol- and polyester-polyol-based rigid urethane foam systems
    Madden, J.P.; Baker, G.K.; Smith, C.H. (1971)

    160

  15. Yield improvement and defect reduction in steel casting
    Kent Carlson (2004)

    125

  16. PROPERTIES AND PERFORMANCE OF CEMENT-BASED GROUTS FOR GEOTHERMAL HEAT PUMP APPLICATIONS.
    ALLAN,M.L. (1999)

    122

  17. Corrosion Testing of Carbon Steel in Acid Cleaning Solutions
    Wiersma, B.J. (2002)

    120

  18. Final Report, Volume 1, Metallurgical Evaluation of Cast Duplex Stainless Steels and their Weldments
    Wen, Songqing; Lundin, Carl, W.; Batten, Greg, W. (2005)

    106

  19. Energy level structure and transition probabilities in the spectra of the trivalent lanthanides in LaF/sub 3/. [Tables, diagrams]
    Carnall, W.T.; Crosswhite, H.; Crosswhite, H.M. (1978)

    103

  20. Metals design handbook
    Betts, W.S. (1988)

    102

Last updated on Tuesday 14 June 2016